產品概述
Product Overview
1.產品特點本充氣目標用料考究，做工精湛。采用真目標尺寸1:1比例，結構合理，外形逼真，示假效果好。同時具有密封性，柔性強，重量輕和貯運方便，架設和撤收速度快等特點。
1. Product features: This inflatable target uses high-quality materials and exquisite workmanship. Adopting a 1:1 ratio of true target size, the structure is reasonable, the appearance is realistic, and the fake effect is good. At the same time, it has the characteristics of sealing, strong flexibility, light weight, convenient storage and transportation, and fast installation and dismantling speed.
2.主要用途及適用范圍可應用于軍事演習，戰場迷惑敵軍等。
2. The main purpose and scope of application can be applied to military exercises, confusing enemy forces on the battlefield, etc.
3.使用環境條件適用使用環境溫度-10℃～55℃。
3. The applicable environmental conditions for use are a temperature range of -10 ℃ to 55 ℃.
使用說明及注意事項
Instructions and precautions for use
1、充氣泵的連續工作時間不能超過20分鐘，超過20分鐘氣泵自然會停止工作。
1. The continuous working time of the inflation pump cannot exceed 20 minutes, and the pump will naturally stop working after 20 minutes.
2、火炮應存放在陰涼干燥的地方。
2. Artillery should be stored in a cool and dry place.
3、現就查找漏洞的方法做個簡單介紹，將預先準備好的肥皂泡水涂抹或噴灑在懷疑漏氣的地方，如果冒泡即此處已經滲漏，應當盡早修補。漏氣修補方法做一個簡單介紹：先目測或尺子測量漏洞大小和位置，選取相應一塊材料，將用于粘合的兩面用刷子均勻刷上膠水，等兩面不粘手為宜，將刷膠的兩面加壓粘合，這樣即完成修補工作。
3. Now let's give a brief introduction to the method of finding vulnerabilities. Apply or spray pre prepared soap and water on the suspected leak area. If it bubbles, it means that the leak has already occurred, and it should be repaired as soon as possible. A brief introduction to the method of repairing air leaks: First, visually inspect or measure the size and location of the leak with a ruler, select a corresponding piece of material, and evenly brush the two sides used for bonding with glue. When the two sides are not sticky, it is advisable to apply pressure and bond the two sides of the glue brush together to complete the repair work.
4、充氣高射炮各部件安裝、裝袋時嚴禁劃傷表面，在地面上嚴禁拖拉。
4. During the installation and bagging of various components of the inflatable anti-aircraft gun, it is strictly prohibited to scratch the surface and drag it on the ground.
5、充放氣閥門使用時注意充、放氣的位置，按下閥門并順時針旋轉為放氣位置，反之，為充氣位置。
5. When using the inflation and deflation valve, pay attention to the position of inflation and deflation. Press the valve and rotate it clockwise to the deflation position, and vice versa to the inflation position.
6、由于環境溫度的變化，有熱脹冷縮現象，長時間使用的充氣火炮應密切關注調節氣體壓力在正常范圍內。因溫度升高應及時通過氣門放氣，以保持氣壓回歸正常。這點是使用此產品的關鍵事項，如果麻痹大意，容易造成破裂隱患。
6. Due to changes in environmental temperature, there may be thermal expansion and contraction phenomena. Inflatable artillery that has been used for a long time should be closely monitored to adjust the gas pressure within the normal range. Due to the increase in temperature, it is necessary to release air through the valve in a timely manner to maintain normal air pressure. This is a key issue when using this product. If one is careless, it can easily cause a risk of rupture.
產品優點
Product advantages
1.整體采用一次性充氣方式制造
1. The entire product is manufactured using a one-time inflation method
2.整體為組合式，有些細節部分采用相應材料代替
2. The overall design is modular, with some details replaced by corresponding materials
3.主體顏色:軍綠色
3. Main color: military green
本文由 充氣假目標 友情奉獻.更多有關的知識請點擊 http://www.yowp.cn/ 真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.
This article is contributed by the inflatable fake target friendship For more related knowledge, please click http://www.yowp.cn/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.
山東三所新材料技術有限公司
聯系電話：13466640666
聯系地址：山東省濟寧市任城區美恒濟寧國際汽車博覽城4號樓2單元0507號
掃碼微信聯系
分類中心