雖然說現在充氣類的拱門已經被應用的很廣泛,但是很多商家或者是個體用戶對于這種常用的工具的具體使用方法以及保養還不是特別了解,這就直接導致一些錯誤的操作,使得拱門的使用壽命大大縮短,甚至在使用過程中,因為操作不當而導致位置不固定、漏氣、發出奇怪的聲音等。下面為大家介紹一下正確的使用方法以及保養的技巧。
Although inflatable arches have been widely used nowadays, many businesses or individual users are not very familiar with the specific usage and maintenance of this commonly used tool, which directly leads to some incorrect operations, greatly shortening the service life of the arch. Even during use, improper operation may cause the position to be unstable, air leakage, strange noises, etc. Below, we will introduce the correct usage method and maintenance techniques for everyone.
一、正確的使用方法1.在使用之前,首先要把電源線固定好。原因很簡單,因為在充氣的過程當中,隨著氣體的不斷膨脹,會使得拱門的體積不斷的變大,這個時候如果事先沒有把電源線固定好,電源線有可能隨著體積膨脹的過程當中出現松動或者脫落現象,輕則可能導致充氣失敗,重則有可能導致觸電事故。所以再次提醒,在使用之前請務必把電源線固執好,并且找到相應的開關和電源位置,電源線固定好之后才可以做下一步的操作。
1、 The correct usage method is to first secure the power cord before use. The reason is simple, because during the inflation process, as the gas continues to expand, the volume of the arch will continue to increase. If the power cord is not fixed in advance, it may loosen or fall off during the expansion process, which may result in inflation failure or electric shock accidents. So once again, please be sure to firmly secure the power cord before use, and find the corresponding switch and power position. Only after fixing the power cord can you proceed to the next step.
2.將充氣拱門擺放在合理的位置,事先綁好繩索,然后向里面充氣就可以了。
2. Place the inflatable arch in a reasonable position, tie the ropes in advance, and then inflate it inside.
二、充氣拱門被劃破怎么做呢?(1)如果劃口的地方大于6厘米應用魚針線縫接。小的劃口就直接黏貼面料就可以了。或從氣墊底部拆開進入縫接。(2)充氣拱門接縫開線:先用針線把開口的地方縫接平坦。然后壓平壓緊。(3)充氣拱門美化的地方翹邊:用刷子在翹邊涂上適當的膠水,黏貼結實就可以了。也可用面料剪成不一樣的外型在脫膠的地方黏貼即可。(4)拱門長時間使用后,漏氣量大增,可思考用面料黏貼于接縫的地方,削減漏氣量,如拱門過于陳舊,應思考作廢,以防運營中出疑問。
2、 How to do if the inflatable arch is scratched? (1) If the incision is greater than 6 centimeters, use fish needle and thread to sew it together. Just stick the fabric directly to the small scratch. Or detach from the bottom of the air cushion and enter the seam. (2) Opening the seam of the inflatable arch: First, use needle and thread to sew the opening flat. Then flatten and press firmly. (3) Beautify the area of the inflatable arch with raised edges: Use a brush to apply appropriate glue to the raised edges and stick them firmly. You can also cut the fabric into different shapes and stick them on the areas where they come off. (4) After prolonged use, the amount of air leakage in the arch increases significantly. It is recommended to use fabric to stick it to the seams to reduce the amount of air leakage. If the arch is too old, it should be considered to be scrapped to prevent problems during operation.
三.拱門保護知識(1)充氣拱門放氣前。曬干后放氣,折疊置陰涼潔凈的地方保管。(2)若充氣拱門保管不善進水。放枯燥通風的地方吹起,晾至水蒸干停止,切忌有水寄存。以防受潮。(3)氣模怕掛破。如同我們穿的衣服一樣,再好的衣料也怕掛撕。使用拱門時,一定要避開空中的樹枝、通訊電纜上的鐵鉤等尖銳物。(4)怕拖。需要移動氣模的擺放位置時,要抬起來再移動。如果拖動的話,時間長了,很容易磨破。(5)怕土炮。在開張慶典場合,炮、煙花是離不開的東西。一定遠離氣模6米以上才可點炮。
III Arche protection knowledge (1) Before inflating the arch and releasing air. After drying, deflate and fold to store in a cool and clean place. (2) If the inflatable arch is not properly stored and water enters. Blow it up in a dry and ventilated place, let it dry until the water evaporates, and avoid storing it with water. To prevent moisture. (3) The air model is afraid of being broken. Just like the clothes we wear, even the best fabric is afraid of tearing. When using arches, be sure to avoid sharp objects such as branches in the air and iron hooks on communication cables. (4) Afraid of procrastination. When it is necessary to move the placement position of the air mold, it should be lifted up before moving. If dragged for a long time, it is easy to wear out. (5) Afraid of soil cannons. At the opening ceremony, cannons and fireworks are indispensable. Be sure to stay at least 6 meters away from the air model before firing.
本文由 充氣拱門 友情奉獻.更多有關的知識請點擊 http://www.yowp.cn/ 真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.
This article is contributed by the inflatable arch friendship For more related knowledge, please click http://www.yowp.cn/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.
山東三所新材料技術有限公司
聯系電話:13466640666
聯系地址:山東省濟寧市任城區美恒濟寧國際汽車博覽城4號樓2單元0507號