面料選擇：采用高強滌綸長絲以井字平格織造方式由噴水織機進行織造，基布重量≤100g/m2，坯布經過精練退漿處理，定形成品有效門幅150mm，這樣既能提高偽裝網面料的拉伸及撕破強力，又能減輕偽裝網的重量，便于架設使用和運輸。
Fabric selection: High strength polyester filament is used to weave in a grid pattern using a water jet loom. The weight of the base fabric is ≤ 100g/m2, and the grey fabric is subjected to scouring and desizing treatment. The effective width of the shaped product is 150mm. This can not only improve the tensile and tear strength of the camouflage net fabric, but also reduce the weight of the camouflage net, making it easy to install, use, and transport.
圖案設計：面料開發時需注重斑塊顏色與斑塊面積的搭配比例，使斑塊之間的過渡更加順暢自然，圖案斑點設計更趨科學，與自然光線投下的斑點深淺度吻合性更高，具有立體層次感，符合自然界的實際情況，從而使偽裝特征更加顯著。
Pattern design: When developing fabrics, attention should be paid to the matching ratio between patch color and patch area to make the transition between patches smoother and more natural. Pattern spot design is more scientific, and has a higher degree of consistency with the depth of spots cast by natural light. It has a three-dimensional sense of hierarchy, which is in line with the actual situation of the natural world, and thus makes the camouflage characteristics more prominent.
涂料選擇：為保證涂料能夠均勻地分散在漿料中，具有較好的穩定性，著色力強，遮蓋力好，耐光性能優越。可選用品種多、色譜廣、色澤鮮艷度和著色力高的有機涂料（白色涂料選擇在紫外光譜內具備高反射率的無機材料）。
Coating selection: To ensure that the coating can be evenly dispersed in the slurry, with good stability, strong coloring power, good covering power, and superior light resistance. Organic coatings with a wide variety, wide spectrum, bright color, and high coloring power can be selected (for white coatings, inorganic materials with high reflectivity in the ultraviolet spectrum can be selected).
阻燃涂色整理：
山東濟寧偽裝網采用涂層的方法賦予面料耐久性阻燃性能，選擇環保阻燃劑與涂層膠并按8∶5比例，輔以所需的有機、無機顏料混合而成，然后在面料兩面各刮涂一次，單面刮涂增重約20～25g/m2，然后在160℃下烘40s。這樣能有效防止在后續印花過程中色漿滲化引起的正反兩面顏色的相互影響，進而保證偽裝網顏色的準確性。這種方法既可以達到面料阻燃的技術要求，同時面料兩面也印上了底色，從而減少了印花的套色數。
Flame retardant coating and finishing: Shandong Jining Camouflage Net uses a coating method to endow the fabric with durability and flame retardancy. It is made by selecting environmentally friendly flame retardants and coating adhesive in a ratio of 8:5, supplemented by the required organic and inorganic pigments. Then, it is scraped and coated once on both sides of the fabric, with a weight gain of about 20-25g/m2 on one side. Then, it is baked for 40 seconds at 160 ℃. This can effectively prevent the mutual influence of the front and back colors caused by color paste infiltration during the subsequent printing process, thereby ensuring the accuracy of the camouflage screen color. This method can not only meet the technical requirements of flame retardant fabric, but also print the base color on both sides of the fabric, thereby reducing the number of color sets in printing.
印花漿料選擇：涂料對纖維沒有親和力，所以不能像染料一樣通過與纖維的相互作用而上染，涂料與纖維的結合必須依賴于黏合劑膜的包覆及黏合劑大分子對纖維的黏附作用。按底膠：面膠∶消光PU膠=4∶3∶3的比例混合，并加入2%的交聯劑、4%的鈦白漿（提高涂料的遮蓋力）、1%的防霉劑，用增稠劑調至合適黏度，攪拌均勻后，制成印花漿備用。將所需顏色的涂料色漿加入印花漿攪拌均勻后印花，烘干后印花表面無黏連現象，各種牢度均較好。
Selection of printing paste: Coatings have no affinity for fibers, so they cannot be dyed through the interaction with fibers like dyes. The binding between coatings and fibers must rely on the coating of adhesive films and the adhesion of adhesive macromolecules to fibers. Mix according to the ratio of base adhesive: surface adhesive: matte PU adhesive=4:3:3, and add 2% cross-linking agent, 4% titanium dioxide slurry (to improve the covering power of the coating), and 1% mold inhibitor. Adjust to the appropriate viscosity with a thickener, stir evenly, and prepare a printing paste for later use. Add the required color pigment paste to the printing paste and stir evenly before printing. After drying, there is no adhesion on the printing surface and all kinds of fastness are good.
確定面料及涂料、漿料后，在經過阻燃涂色整理的面料上按色光要求進行印花打樣配色，配色結束后，需要配制每種顏色生產所需的色漿，色漿配好后需要再次復小樣確定每種顏色色光是否符合要求，只有符合色光要求后才能用于平網印花。更多相關事項歡迎來我們網站
http://www.yowp.cn咨詢吧！
After determining the fabric, coating, and size, print and match according to the color requirements on the flame retardant coated fabric. After the color matching is completed, the necessary color paste for each color production needs to be prepared. After the color paste is prepared, it needs to be re sampled to determine whether each color meets the requirements. Only after meeting the color light requirements can it be used for flat screen printing. Welcome to our website for more related matters http://www.yowp.cn Consult!
山東三所新材料技術有限公司
分類中心